Settings Dictionary
What each adjuster and measurement actually does. It covers where to measure from (a number means nothing without it), which way counts as more or less, mistakes people make, and what the manufacturer says. This is reference reading only — nothing here is about your own bike.
Showing 151–200 of 648 entries
Five-plus-way / factory development shock
How it is built · ShockUnverifiedAdds bottoming, bypass, hydraulic stop, or additional map controls Classification axis: Adjustment level Advantages: Fine control of separate events/positions R…
Foam-cell shock
How it is built · ShockUnverifiedGas is distributed in closed-cell foam to reduce free aeration Classification axis: Oil/gas relationship Advantages: Compact without high-pressure separator har…
Fork air pressure
AdjustmentsUnverifiedProvisional entry auto-created from the existing settings parameter pending curation. SI unit: Pa. Direction of increase: increase_pressure.
Fork bottoming — Hydraulic cone/cup geometry
Inside the fork or shockUnverifiedLate-stroke damping
Fork cap protrusion / adjustable length
AdjustmentsUnverifiedChanges overall fork length or clamp datum Part / location: Fork cap/extension
Fork cartridge — Base-valve stack
Inside the fork or shockUnverifiedCompression and cartridge pressure management
Fork cartridge — Bleed jet / hole
Inside the fork or shockUnverifiedLow-speed bypass
Fork cartridge — Cartridge pressure
Inside the fork or shockUnverifiedCavitation resistance and friction
Fork cartridge — Check-valve spring/plate
Inside the fork or shockUnverifiedOne-way refill and low-flow behavior
Fork cartridge — Compression shim stack
Inside the fork or shockUnverifiedPressure-dependent compression damping
Fork cartridge — Main compression piston
Inside the fork or shockUnverifiedCompression force curve and pressure distribution
Fork cartridge — Mid-valve compression stack
Inside the fork or shockUnverifiedMid/high-flow compression control
Fork cartridge — Mid-valve float
Inside the fork or shockUnverifiedInitial compression engagement
Fork cartridge — Needle taper and seat
Inside the fork or shockUnverifiedExternal-adjuster sensitivity and range
Fork cartridge — Rebound piston
Inside the fork or shockUnverifiedRebound curve and cavitation margin
Fork cartridge — Rebound shim stack
Inside the fork or shockUnverifiedExtension damping
Fork combined compression/rebound
AdjustmentsUnverifiedChanges both directions together Part / location: Single external damping control
Fork compression
AdjustmentsUnverifiedProvisional entry auto-created from the existing settings parameter pending curation. Direction of increase: increase_damping_force.
Fork damping — Oil viscosity
Inside the fork or shockUnverifiedDamping and temperature sensitivity
Fork fluid viscosity
AdjustmentsUnverifiedChanges flow resistance and temperature behavior Part / location: Fork damping circuit
Fork friction — Bushing clearance
Inside the fork or shockUnverifiedFriction, guidance and oil film
Fork friction — Seal and wiper design
Inside the fork or shockUnverifiedSmall-bump sensitivity and hysteresis
Fork fully extended length
Other setup numbers · Front geometryUnverifiedAxle-center to cap/clamp reference at full extension. Primary performance effect: Sets base front height and available geometry range. Category: Fork assembly
Fork height in clamps
Other setup numbersUnverifiedProvisional entry auto-created from the existing settings parameter pending curation. SI unit: m. Direction of increase: raise_front.
Fork height in triple clamps
AdjustmentsUnverifiedChanges front ride height, rake, trail and weight distribution Part / location: Upper tube position relative to top clamp
Fork height / protrusion
MeasurementsUnverifiedFork reference surface above/below upper clamp datum Scope: Front geometry
Fork high-speed compression
AdjustmentsUnverifiedControls rapid damper-shaft events and pressure-sensitive valve opening Part / location: Fork cap/base/reservoir, uncommon on road forks
Fork high-speed rebound
AdjustmentsUnverifiedControls rapid extension events Part / location: Fork cap/base, rare external race control
Fork-leg center spacing
Other setup numbers · Front geometryUnverifiedLeft-to-right fork center distance. Primary performance effect: Affects fitment, torsional stiffness and wheel/brake location. Category: Triple clamps
Fork-leg parallelism / stiction
Other setup numbers · Front geometryUnverifiedSide load or twist in fork/axle/clamp assembly. Primary performance effect: Changes small-bump response, braking feel and effective damping. Category: Alignment
Fork location relative to top clamp
Other setup numbers · Front geometryUnverifiedWhether the fork/clip-on stack is above, flush with or below the top clamp. Primary performance effect: Changes cockpit packaging and sometimes ride height. Cat…
Fork low-speed compression
AdjustmentsUnverifiedControls slower chassis movements such as braking load transfer Part / location: Fork cap or bottom
Fork oil air gap
MeasurementsUnverifiedDistance from tube reference to oil surface Scope: Fork
Fork oil height / air gap
AdjustmentsUnverifiedTunes trapped-air progression and lubrication volume Part / location: Fork outer chamber
Fork oil volume
AdjustmentsUnverifiedSets fill quantity Part / location: Fork leg/cartridge
Fork outer chamber — Oil height / air gap
Inside the fork or shockUnverifiedEnd-stroke air-spring progression
Fork outer chamber — Oil volume
Inside the fork or shockUnverifiedLubrication, cooling and air volume
Fork preload
AdjustmentsUnverifiedProvisional entry auto-created from the existing settings parameter pending curation. Direction of increase: increase_preload.
Fork rebound
AdjustmentsUnverifiedProvisional entry auto-created from the existing settings parameter pending curation. Direction of increase: increase_damping_force.
Fork rebound damping
AdjustmentsUnverifiedControls how quickly fork extends after compression Part / location: Fork cap or bottom, model-specific
Fork/shock fluid viscosity
MeasurementsUnverifiedKinematic viscosity at stated temperature Scope: Fluid
Fork spring — Preload spacer length
Inside the fork or shockUnverifiedInitial force and sag
Fork spring rate
MeasurementsUnverifiedSlope of force-deflection curve in working range Scope: Fork spring
Fork spring — Spring rate
Inside the fork or shockUnverifiedSag, support and wheel rate
Fork structure — Surface coating
Inside the fork or shockUnverifiedFriction and wear
Fork structure — Tube straightness/runout
Inside the fork or shockUnverifiedFriction, seal life and alignment
Fork top-out — Top-out spring
Inside the fork or shockUnverifiedFull-extension control and initial force
Fork travel — Internal travel spacer
Inside the fork or shockUnverifiedMaximum travel and ride height
Fork-tube protrusion
Other setup numbers · Front geometryUnverifiedFork height above the upper triple clamp. Primary performance effect: Changes front ride height, rake, trail, wheelbase and clearance. Category: Fork position
Fork tubes moved upward
How settings affect each otherUnverifiedUsually lowers front ride height; changes rake, trail, wheelbase, weight distribution, clearance and rider/clip-on packaging.